How the Difference between Porsche piwis 3 and piwis tester 2 VCI?

 Along porsche piwis tester iii diagnostic and programming tool released, lots of customers may confused about Porsche tester Piwis 2 or Piwis 3 which one to choose? Is it worth to purchase Piwis 3 replace Piwis 2 now? Can Samtec Piwis 2 compatible with Piwis 3 Software?

Here OBD2cartool.com will share you Porsche Piwis 3 Compare With Porsche Piwis Tester 2.

High Quality Samtec Piwis 2 tester Wifi Piwis II VCI for Porsche

Porsche Piwis 3 Tester III Diagnostic With V39.500 Software Installed on Lenovo Ready to use

 

Differences between Porsche piwis tester iii with Piwis tester 2?

First of all, the Piwis 2 interface is a lot more robust piece of equipment, compared to the cheesy and flimsy looking and feeling interface produced by Actia for Piwis 3.

Secondly, Piwis 2 vci latest software 18.15 support till 2018 car models best price from obd2cartool.com $369.99. Porsche Piwis 3 Tester III Diagnostic With V39.500 Software Installed on Lenovo Ready to use Support all Porsche till 2020 best price $1,299.00. If you have a garage for many newer car models you do better to choose Piwis tester 3.

Third, Porsche PIWIS III which sell with laptop and software installed ready to use. You can get both cases the VCI and software have been modified to disable factory authentication and naturally there is no automatic updates. If you did have a PPN account, this tool would update normally.

Finally About Piwis 2 and Piwis 3 Update: Piwis 2 you can only buy a new HDD OR SSD to update. Piwis 3 you need to Send Laptop with SSD back to upgrade, 1 year for free, after one year, 100usd/time. You can also Send SSD back or buy a new SSD.

More message welcome contact with WhatsAPP(+86-13537734676) or Skype(great2obd) for Nice price.

How to replace and programming Mercedes ME 9.7?

How to replace and programming Mercedes ME 9.7? 

Mercedes ME 9.7 ECU is a more frequently replaced parts,obd2cartool will show you a step-by-step guide on how to use KTAG to read/write Mercedes Benz ME9.7 And try this procedures at your own risk!

How to replace and program Me 9.7 with Ktag:

You need:

Ktag or KTM100 (to help write data)

Mercedes ME 9.7 ECU (for replacement)

Renew cable (to write data into the new ECU)

Step 1: Remove the ME9.7 ECU from vehicle,and open the ECU shell carefully.

Step 2: read and save original ECU data with Ktag programmer

Connect then cable 14P600KT02 to the connector of ECU.

Refer to below pin out diagram:

Red color: Pin 15, 16: +12V

Black: Pin 2: GND

Apply solder paste on the red area in ECU

used K-TAG ecu chip tuning tool to read out Mercedes ME9.7 ECU 

Step 3: connect the new ECU and Ktag with the ME9.7 renew cable

Step 4: write the data into the new ECU with KTAG 7.020 

When you get the original ECU data, just use this renew cable to connect to Ktag to write to Mercedes ME9.7 ME 9.7 ECU.  With this cable, you won’t need to open the ECU to write data anymore.

How about the China Mercedes ME9.7 ECU ECM Engine Computer ?

Mercedes ME9.7 ECU ECM Engine Computer ME 9.7 Programming work All Series 237 Engine 4.6L 4633CC V8/5.5L5641CC V8

1. Mercedes ME9.7 ECU Engine Computer can program it online directly.

2. Unlock an used ME9.7 ECM in order to adapt it with SDS, Autologic, etc

3. Can work with KTAG/KTM100 to read and write ECU data for your car new ECU.

4. If work with Mercedes Benz ECU ME9.7/272-273/ Renew Cable , there no need to remove the ecu from the car when programming new ecu.

5. Can work with MB SD C4/C5 to do online programming with SCN code.

6. No need for additional programming, just install the new ECM and the car will start! 

Note: The ME9.7 renew cable CANNOT be connected to original ME9.7 ECU computer. It is confirmed to work with Me 9.7 ecu without issue. 

How to install DIY MQB HEX V2 VCDS 20.12.0 software?

How to install Or update DIY MQB HEX V2 VCDS 19.6.2 software?
DIY Hex-v2 20.12.0 is the new generation of vag com vcds obd2 diagnostic interface for vag vehicles.  DIY MQB platform HEX V2 VAG model year coverage from 1995 – 2020 year. It is work with MQB cars and MY2020.


DIY VAG COM 20.12.0 HEX V2 Interface MQB HEX V2 unlimited VIN Diagnostic Cable for VW Audi Seat Skoda

MQB HEX-V2 20.12.0 Intelligent Dual-K & CAN USB Interface Car Auto Fault Diagnosis cable install guide:

Install English version steps:
1. Download the original Release 20.12.0 from the offcial website or Copy the program from obd2cartool.com CD
2. Install VCDS 20.12.0 , when installing any software not plug the cable with your pc(Note: if your pc is 64bits, pls choose the option install 32bits to 64bits)
3. Plug MQB HEX V2 interface into the car and pc, run vcds 19.6.2, first time pls click test and save.
do the risk by yourself.


Install other language steps: (French, German, Russian, Italian, Swedish, Danish, Czech, polish, Dutch, Hungarian, Portuguese, Spanish, Slovenia, Romania.)
1. Download the original Release -XX-20.4.2 from the offcial website or Copy the program from obd2cartool.com CD
2. Install VCDS-XX- 20.4.2 , when installing any software not plug the cable with your pc
3. Install the V2 Loader-EN-Installer.exe
3. Plug MQB HEX V2 interface into the car and pc, run VIIPlusLoader , click start VCDS,  choose the language you want or pull the vcds-XX- shortcut into loader . first time pls click test and save.
Do the risk by yourself.

Whatsapp:+86-13537734676
Email: obd2cartool@hotmail.com
Skype: great2obd
If you have any problem, please do not hesitate to contact us.